File:  [DragonFly] / src / nrelease / root / README
Revision 1.1: download - view: text, annotated - select for diffs
Mon Dec 1 21:14:02 2003 UTC (10 years, 9 months ago) by dillon
Branches: MAIN
CVS tags: HEAD
Add a README file, rc.conf, and example fstab.  Disable a number of system
gizmos in the rc.conf that don't make sense for a CD boot, like syslog
and cron.

			    DRAGONFLY CDROM README FILE

    This CDROM boots DragonFly BSD.  Basically what you get is a full base
    system on CD with certain critical directories, such as /tmp, remounted
    read-write using MFS.  Your existing hard drive is not effected by
    booting this CDROM.

    NOTE!!! DRAGONFLY IS UNDERGOING DEVELOPMENT AND CONSIDERED EXPERIMENTAL!
    BSD RELATED EXPERIENCE IS REQUIRED TO USE THIS CDROM.

    If you just want to play with DragonFly and not mess with your hard disk,
    this CDROM boots into a fully operational console-based system, though
    without swap it should be noted that you are limited by available memory.

			    AUTOMATIC INSTALLATION

    We are currently developing automatic installation tools.  There are none
    on this CD.

			    MANUAL INSTALLATION

    Manual installation of DragonFly onto an HD involve the following sequence
    of commands.  You must be familiar with BSD style UNIX systems to do
    installations manually.  The primary IDE hard drive is typically 'ad0'
    and DragonFly is typically installed onto the first slice.


	# This COMPLETE WIPES and repartitions your hard drive
	fdisk -IB ad0

	# This installs boot blocks onto the HD and verifies their 
	# installation.
	boot0cfg -B ad0
	boot0cfg -v ad0

	# This creates an initial label on the first slice of the HD.  If
	# you have problems booting you could try wiping the first 32 blocks
	# of the slice with dd and then reinstalling the label
	#
	# dd if=/dev/zero of=/dev/ad0s1 bs=32k count=16
	disklabel -B -r -w ad0s1 auto

	# Edit the label.  Create various standard partitions.  The typical
	# configurations is:
	#
	#	ad0s1a	256m		This will be your /
	#	ad0s1b	1024m		This will be your swap
	#	ad0s1c			(leave alone)
	#	ad0s1d	256m		This will be your /var
	#	ad0s1e	256m		This will be your /tmp
	#	ad0s1f	8192m		This will be your /usr (min 4096m)
	#	ad0s1g	*		All remaining space to yoru /home
	#
	disklabel -e ad0s1

	# Newfs (format) the various filesystems.  Softupdates is not 
	# normally enabled on the root filesystem.
	#
	newfs /dev/ad0s1a
	newfs -U /dev/ad0s1d
	newfs -U /dev/ad0s1e
	newfs -U /dev/ad0s1f
	newfs -U /dev/ad0s1g

	# Mount the filesystems
	#
	mount /dev/ad0s1a /mnt
	mkdir /mnt/var
	mkdir /mnt/tmp
	mkdir /mnt/usr
	mkdir /mnt/home
	mount /dev/ad0s1d /mnt/var
	mount /dev/ad0s1e /mnt/tmp
	mount /dev/ad0s1f /mnt/usr
	mount /dev/ad0s1g /mnt/home

	# Copy the CDRom onto the target.  cpdup won't cross mount boundaries
	# on the source (e.g. the MFS remounts) so it takes a few commands.
	#
	cpdup / /mnt
	cpdup /var /mnt/var
	cpdup /etc /mnt/etc
	cpdup /dev /mnt/dev

	# Edit /mnt/etc/fstab to reflect the new mounts.  An example fstab
	# file based on the above parameters exists as /mnt/etc/fstab.example
	# which you can rename to /mnt/etc/fstab.
	#
	mv /mnt/etc/fstab.example /mnt/etc/fstab
	vi /mnt/etc/fstab

    Once you've duplicated the CD onto your HD you have to make some edits
    so the system boots properly from your HD.  Primarily you must remove
    or edit /mnt/boot/loader.conf

	# Remove /mnt/boot/loader.conf so the kernel does not try to
	# obtain the root filesystem from the CD.
	#
	rm /mnt/boot/loader.conf

    At this point it should be possible to reboot.  The CD may be locked
    since it is currently mounted.  Be careful of the CD drawer closing
    on you when you open it during the reboot.  Remove the CD and allow
    the system to boot from the HD.

	# reboot
	reboot
	(remove CD when convenient, be careful of the CD drawer closing on you)

    Once you have a working HD based system you can clean up /etc/rc.conf
    to enable things like cron, sendmail, setup your networking, and so
    forth.  If 'ifconfig' does not show your networking device you could
    try to kldload it from /modules.  With a recognized network device
    you can ifconfig its IP address or, if you have a DHCP server on your
    network, use 'dhclient <interfacename>' to obtain an IP address from
    the netweork.

    This CD contains two pre-installed ports:  cvsup and mkisofs.  cvsup
    can be used to obtain the DragonFly cvs repository, the FreeBSD ports
    tree, and so on and so forth.  'man cvsup' for more information.
    The cvsup example files are in /usr/share/examples/cvsup.  You will
    primarily be interested in the DragonFly CVS repository, DragonFly-supfile,
    and the FreeBSD ports, FreeBSD-ports-supfile.

$DragonFly: src/nrelease/root/README,v 1.1 2003/12/01 21:14:02 dillon Exp $