DragonFly On-Line Manual Pages
RUN(4) DragonFly Kernel Interfaces Manual RUN(4)
run -- Ralink Technology USB IEEE 802.11a/g/n wireless network device
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
Firmware is also needed, and provided by:
Alternatively, to load the driver as a module at boot time, place the
following lines in loader.conf(5):
The run driver supports USB 2.0 wireless adapters based on the Ralink
RT2700U, RT2800U, RT3000U and RT3900E chipsets.
The RT2700U chipset consists of two integrated chips, an RT2770 MAC/BBP
and an RT2720 (1T2R) or RT2750 (dual-band 1T2R) radio transceiver.
The RT2800U chipset consists of two integrated chips, an RT2870 MAC/BBP
and an RT2820 (2T3R) or RT2850 (dual-band 2T3R) radio transceiver.
The RT3000U is a single-chip solution based on an RT3070 MAC/BBP and an
RT3020 (1T1R), RT3021 (1T2R) or RT3022 (2T2R) single-band radio trans-
The RT3900E is a single-chip USB 2.0 802.11n solution. The MAC/Baseband
Processor can be an RT3593, RT5390, RT5392 or an RT5592. The radio can
be an RT3053, RT5370, RT5372 or an RT5572. The RT3053 chip operates in
the 2GHz and 5GHz spectra and supports up to 3 transmit paths and 3
receiver paths (3T3R). The RT5370 chip operates in the 2GHz spectrum and
supports 1 transmit path and 1 receiver path (1T1R). The RT5372 chip
operates in the 2GHz spectrum and supports up to 2 transmit paths and 2
receiver paths (2T2R). The RT5572 chip operates in the 2GHz and 5GHz
spectra and supports up to 2 transmit paths and 2 receiver paths (2T2R).
These are the modes the run driver can operate in:
BSS mode Also known as infrastructure mode, this is used when asso-
ciating with an access point, through which all traffic
passes. This mode is the default.
Host AP mode In this mode the driver acts as an access point (base sta-
tion) for other cards.
monitor mode In this mode the driver is able to receive packets without
associating with an access point. This disables the
internal receive filter and enables the card to capture
packets from networks which it wouldn't normally have
access to, or to scan for access points.
The run driver can be configured to use Wired Equivalent Privacy (WEP) or
Wi-Fi Protected Access (WPA-PSK and WPA2-PSK). WPA is the de facto
encryption standard for wireless networks. It is strongly recommended
that WEP not be used as the sole mechanism to secure wireless communica-
tion, due to serious weaknesses in it. The run driver offloads both
encryption and decryption of data frames to the hardware for the WEP40,
WEP104, TKIP(+MIC) and CCMP ciphers.
The run driver can be configured at runtime with ifconfig(8).
The run driver supports the following wireless adapters:
ASUS USB-N13 ver. A1
Belkin F5D8051 ver 3000
Belkin F6D4050 ver 1
D-Link DWA-130 rev B1
D-Link DWA-140 rev B1, B2, B3, D1
D-Link DWA-160 rev B2
DrayTek Vigor N61
Linksys WUSB54GC v3
Mvix Nubbin MS-811N
TP-LINK TL-WN727N v3
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan create wlandev run0 inet 192.168.0.20 \
Join a specific BSS network with network name ``my_net'':
ifconfig wlan create wlandev run0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan create wlandev run0 ssid my_net \
wepmode on wepkey 0x1234567890 weptxkey 1 up
Join a specific BSS network with 128-bit WEP encryption:
ifconfig wlan create wlandev run0 wlanmode adhoc ssid my_net \
wepmode on wepkey 0x01020304050607080910111213 weptxkey 1
run%d: faild load firmware of file runfw For some reason, the driver was
unable to read the microcode file from the filesystem. The file might be
missing or corrupted.
run%d: could not load 8051 microcode An error occurred while attempting
to upload the microcode to the onboard 8051 microcontroller unit.
run%d: device timeout A frame dispatched to the hardware for transmis-
sion did not complete in time. The driver will reset the hardware. This
should not happen.
ifmedia(4), intro(4), netintro(4), runfw(4), usb(4), wlan(4),
wlan_amrr(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), wlan_xauth(4),
hostapd(8), ifconfig(8), wpa_supplicant(8)
Ralink Technology: http://www.ralinktech.com/
The run driver first appeared in OpenBSD 4.5.
The run driver was written by Damien Bergamini <firstname.lastname@example.org>.
The run driver does not support any of the 802.11n capabilities offered
by the RT2800, RT3000 and RT3900 chipsets.
DragonFly 4.9 May 15, 2016 DragonFly 4.9