DragonFly On-Line Manual Pages
VIDCONTROL(1) DragonFly General Commands Manual VIDCONTROL(1)
vidcontrol -- system console control and configuration utility
vidcontrol [-CdLPpx] [-b color] [-c appearance] [-f [size] file]
[-g geometry] [-h size] [-i adapter | mode] [-l screen_map]
[-M char] [-m on | off] [-r foreground background]
[-S on | off] [-s number] [-t N | off] [mode]
[foreground [background]] [show]
The vidcontrol command is used to set various options for the syscons(4)
console driver, such as video mode, colors, cursor shape, screen output
map, font and screen saver timeout.
The following command line options are supported:
mode Select a new video mode. The modes currently recognized are:
80x25, 80x30, 80x43, 80x50, 80x60, 132x25, 132x30, 132x43,
132x50, 132x60, VGA_40x25, VGA_80x25, VGA_80x30, VGA_80x50,
VGA_80x60, VGA_90x25, VGA_90x30, VGA_90x43, VGA_90x50, VGA_90x60,
EGA_80x25, EGA_80x43. Alternatively, a mode can be specified
with its number by using a mode name of the form MODE_<NUMBER>.
A list of valid mode numbers can be obtained with the -i mode
option. See Video Mode Support below.
Change colors when displaying text. Specify the foreground color
(e.g. ``vidcontrol white''), or both a foreground and background
colors (e.g. ``vidcontrol yellow blue''). Use the show command
below to see available colors.
show See the supported colors on a given platform.
Set border color to color. This option may not be always sup-
ported by the video driver.
-C Clear the history buffer.
-c normal | blink | destructive
Change the cursor appearance. The cursor is either an inverting
block (normal) that can optionally blink, or it can be like the
old hardware cursor (destructive). The latter is actually a sim-
-d Print out current output screen map.
-f [size] file
Load font file for size (currently, only 8x8, 8x14 or 8x16). The
font file can be either uuencoded or in raw binary format. You
can also use the menu-driven vidfont(1) command to load the font
of your choice.
Size may be omitted, in this case vidcontrol will try to guess it
from the size of font file.
See also Video Mode Support and EXAMPLES below and the man page
Set the geometry of the text mode for the modes with selectable
geometry. Currently only raster modes support this option. See
also Video Mode Support and EXAMPLES below.
Set the size of the history (scrollback) buffer to size lines.
Shows info about the current video adapter.
Shows the possible video modes with the current video hardware.
Install screen output map file from screen_map. See also
-L Install default screen output map.
Sets the base character used to render the mouse pointer to char.
-m on | off
Switch the mouse pointer on or off. Used together with the
moused(8) daemon for text mode cut & paste functionality.
-p Capture the current contents of the video buffer corresponding to
the terminal device referred to by standard input. The
vidcontrol utility writes contents of the video buffer to the
standard output in a raw binary format. For details about that
format see Format of Video Buffer Dump below.
-P Same as -p, but dump contents of the video buffer in a plain text
format ignoring nonprintable characters and information about
-r foreground background
Change reverse mode colors to foreground and background.
-S on | off
Turn vty switching on or off. When vty switching is off,
attempts to switch to a different virtual terminal will fail.
(The default is to permit vty switching.)
Set the current vty to number.
-t N | off
Set the screensaver timeout to N seconds, or turns it off.
-x Use hexadecimal digits for output.
Video Mode Support
Note that not all modes listed above may be supported by the video hard-
ware. You can verify which mode is supported by the video hardware,
using the -i mode option.
You need to compile your kernel with the VGA_WIDTH90 option if you wish
to use VGA 90 column modes (see vga(4)).
Video modes other than 25 and 30 line modes may require specific size of
font. Use -f option above to load a font file to the kernel. If the
required size of font has not been loaded to the kernel, vidcontrol will
fail if the user attempts to set a new video mode.
Modes Font size
25 line modes 8x16 (VGA), 8x14 (EGA)
30 line modes 8x16
43 line modes 8x8
50 line modes 8x8
60 line modes 8x8
It is better to always load all three sizes (8x8, 8x14 and 8x16) of the
You may set variables in /etc/rc.conf or /etc/rc.conf.local so that
desired font files will be automatically loaded when the system starts
up. See below.
If you want to use any of the raster text modes you need to recompile
your kernel with the SC_PIXEL_MODE option. See syscons(4) for more
details on this kernel option.
Format of Video Buffer Dump
The vidcontrol utility uses the syscons(4) CONS_SCRSHOT ioctl(2) to cap-
ture the current contents of the video buffer. The vidcontrol utility
writes version and additional information to the standard output, fol-
lowed by the contents of the terminal device.
PC video memory is typically arranged in two byte tuples, one per charac-
ter position. In each tuple, the first byte will be the character code,
and the second byte is the character's color attribute.
The color attribute byte is further broken down into the low nibble,
which specifies which of 16 different foreground colors is active, and
the high nibble, which specifies which of 16 different background colors
9 Light Blue
10 Light Green
11 Light Cyan
12 Light Red
13 Light Magenta
It can be seen that the last 8 colors are brighter versions of the first
For example, the two bytes
specify an uppercase A (character code 65), in yellow (low nibble 15) on
a light blue background (high nibble 9).
The vidcontrol output contains a small header which includes additional
information which may be useful to utilities processing the output.
The first 10 bytes are always arranged as follows:
Byte Range Contents
1 thru 8 Literal text ``SCRSHOT_''
9 File format version number
10 Remaining number of bytes in the header
Subsequent bytes depend on the version number.
Version Byte Meaning
1 11 Terminal width, in characters
12 Terminal depth, in characters
13 and up The snapshot data
So a dump of an 80x25 screen would start (in hex)
53 43 52 53 48 4f 54 5f 01 02 50 19
----------------------- -- -- -- --
| | | | ` 25 decimal
| | | `--- 80 decimal
| | `------ 2 remaining bytes of header data
| `--------- File format version 1
`------------------------ Literal "SCRSHOT_"
VIDEO OUTPUT CONFIGURATION
Boot Time Configuration
You may set the following variables in /etc/rc.conf or /etc/rc.conf.local
in order to configure the video output at boot time.
blanktime Sets the timeout value for the -t option.
font8x16, font8x14, font8x8
Specifies font files for the -f option.
scrnmap Specifies a screen output map file for the -l option.
See rc.conf(5) for more details.
The video card driver may let you change default configuration options,
such as the default font, so that you do not need to set up the options
at boot time. See video card driver manuals, (e.g. vga(4)) for details.
/usr/share/syscons/fonts/* font files.
/usr/share/syscons/scrnmaps/* screen output map files.
If you want to load /usr/share/syscons/fonts/iso-8x16.fnt to the kernel,
run vidcontrol as:
vidcontrol -f 8x16 /usr/share/syscons/fonts/iso-8x16.fnt
So long as the font file is in /usr/share/syscons/fonts, you may abbrevi-
ate the file name as iso-8x16:
vidcontrol -f 8x16 iso-8x16
Furthermore, you can also omit font size ``8x16'':
vidcontrol -f iso-8x16
Moreover, the suffix specifying the font size can be also omitted; in
this case, vidcontrol will use the size of the currently displayed font
to construct the suffix:
vidcontrol -f iso
Likewise, you can also abbreviate the screen output map file name for the
-l option if the file is found in /usr/share/syscons/scrnmaps.
vidcontrol -l iso-8859-1_to_cp437
The above command will load
The following command will capture the contents of the first virtual ter-
minal, and redirect the output to the shot.scr file:
vidcontrol -p < /dev/ttyv0 > shot.scr
The following command will dump contents of the fourth virtual terminal
to the standard output in the human readable format:
vidcontrol -P < /dev/ttyv3
kbdcontrol(1), vidfont(1), keyboard(4), screen(4), syscons(4), vga(4),
rc.conf(5), kldload(8), moused(8), watch(8)
The various scr2* utilities in the graphics and textproc categories of
the Ports Collection.
Soren Schmidt <sos@FreeBSD.org>
DragonFly 5.1 August 14, 2015 DragonFly 5.1