DragonFly On-Line Manual Pages
XL(4) DragonFly Kernel Interfaces Manual XL(4)
xl -- 3Com Etherlink XL and Fast Etherlink XL ethernet device driver
The xl driver provides support for PCI ethernet adapters and embedded
controllers based on the 3Com "boomerang" and "cyclone" bus-master Ether-
link XL chips. This includes the 3c900-TP, 3c900-COMBO, 3c905-TX,
3c905-T4, 3c905B-TP, 3c905B-T4 and 3c905B-TX, and embedded 3c905-TX and
3c905B-TX ethernet hardware in certain Dell Optiplex and Dell Precision
desktop machines, and certain Dell Latitude laptop docking stations.
The Etherlink XL chips support built-in 10baseT, 10base2 and 10base5
transceivers as well as an MII bus for externally attached PHY trans-
ceivers. The 3c905 series typically uses a National Semiconductor NS
83840A 10/100 PHY for 10/100 Mbps support in full or half-duplex. The
3c905B adapters have built-in autonegotiation logic mapped onto the MII
for compatibility with previous drivers. Fast Etherlink XL adapters such
as the 3c905-TX and 3c905B-TX are capable of 10 or 100Mbps data rates in
either full or half duplex and can be manually configured for any sup-
ported mode or automatically negotiate the highest possible mode with a
The xl driver supports the following media types:
autoselect Enable autoselection of the media type and options.
Note that this option is only available with the
3c905 and 3c905B adapters with external PHYs or
built-in autonegotiation logic. For 3c900
adapters, the driver will choose the mode specified
in the EEPROM. The user can change this by adding
media options to the /etc/rc.conf file.
10baseT/UTP Set 10Mbps operation. The mediaopt option can also
be used to select either full-duplex or half-duplex
100baseTX Set 100Mbps (fast ethernet) operation. The
mediaopt option can also be used to select either
full-duplex or half-duplex modes.
10base5/AUI Enable AUI transceiver (available only on COMBO
10base2/BNC Enable BNC coax transceiver (available only on
The xl driver supports the following media options:
full-duplex Force full duplex operation
half-duplex Force half duplex operation.
Note that the 100baseTX media type is only available if supported by the
adapter. For more information on configuring this device, see
ifconfig(8). The xl driver supports polling(4).
xl%d: couldn't map memory A fatal initialization error has occurred.
xl%d: couldn't map interrupt A fatal initialization error has occurred.
xl%d: device timeout The device has stopped responding to the network,
or there is a problem with the network connection (cable).
xl%d: no memory for rx list The driver failed to allocate an mbuf for
the receiver ring.
xl%d: no memory for tx list The driver failed to allocate an mbuf for
the transmitter ring when allocating a pad buffer or collapsing an mbuf
chain into a cluster.
xl%d: command never completed! Some commands issued to the 3c90x ASIC
take time to complete: the driver is supposed to wait until the 'command
in progress' bit in the status register clears before continuing. In
rare instances, this bit may not clear. To avoid getting caught in an
infinite wait loop, the driver only polls the bit for a finite number of
times before giving up, at which point it issues this message. This mes-
sage may be printed during driver initialization on slower machines. If
you see this message but the driver continues to function normally, the
message can probably be ignored.
xl%d: chip is in D3 power state -- setting to D0 This message applies
only to 3c905B adapters, which support power management. Some operating
systems place the 3c905B in low power mode when shutting down, and some
PCI BIOSes fail to bring the chip out of this state before configuring
it. The 3c905B loses all of its PCI configuration in the D3 state, so if
the BIOS does not set it back to full power mode in time, it won't be
able to configure it correctly. The driver tries to detect this condi-
tion and bring the adapter back to the D0 (full power) state, but this
may not be enough to return the driver to a fully operational condition.
If you see this message at boot time and the driver fails to attach the
device as a network interface, you will have to perform second warm boot
to have the device properly configured.
Note that this condition only occurs when warm booting from another oper-
ating system. If you power down your system prior to booting DragonFly,
the card should be configured correctly.
xl%d: WARNING: no media options bits set in the media options register!
This warning may appear when using the driver on some Dell Latitude dock-
ing stations with built-in 3c905-TX adapters. For whatever the reason,
the 'MII available' bit in the media options register on this particular
equipment is not set, even though it should be (the 3c905-TX always uses
an external PHY transceiver). The driver will attempt to guess the proper
media type based on the PCI device ID word. The driver makes a lot of
noise about this condition because the author considers it a manufactur-
arp(4), ifmedia(4), miibus(4), netintro(4), ng_ether(4), polling(4),
The xl device driver first appeared in FreeBSD 3.0.
The xl driver was written by Bill Paul <firstname.lastname@example.org>.
DragonFly 5.1 August 16, 1998 DragonFly 5.1