DragonFly On-Line Manual Pages

Search: Section:  

MICROSEQ(9)	      DragonFly Kernel Developer's Manual	   MICROSEQ(9)


microseq -- ppbus microsequencer developer's guide


#include <sys/types.h> #include <sys/bus.h> #include <bus/ppbus/ppbconf.h> #include <bus/ppbus/ppb_msq.h>


See ppbus(4) for ppbus description and general info about the microse- quencer. The purpose of this document is to encourage developers to use the microsequencer mechanism in order to have: 1. a uniform programming model 2. efficient code Before using microsequences, you are encouraged to look at ppc(4) microsequencer implementation and an example of how using it in vpo(4). PPBUS register model Background The parallel port model chosen for ppbus is the PC parallel port model. Thus, any register described later has the same semantic than its coun- terpart in a PC parallel port. For more info about ISA/ECP programming, get the Microsoft standard referenced as "Extended Capabilities Port Pro- tocol and ISA interface Standard". Registers described later are standard parallel port registers. Mask macros are defined in the standard ppbus include files for each valid bit of parallel port registers. Data register In compatible or nibble mode, writing to this register will drive data to the parallel port data lines. In any other mode, drivers may be tri- stated by setting the direction bit (PCD) in the control register. Reads to this register return the value on the data lines. Device status register This read-only register reflects the inputs on the parallel port inter- face. Bit Name Description 7 nBUSY inverted version of parallel port Busy signal 6 nACK version of parallel port nAck signal 5 PERROR version of parallel port PERROR signal 4 SELECT version of parallel port Select signal 3 nFAULT version of parallel port nFault signal Others are reserved and return undefined result when read. Device control register This register directly controls several output signals as well as enabling some functions. Bit Name Description 5 PCD direction bit in extended modes 4 IRQENABLE 1 enables an interrupt on the rising edge of nAck 3 SELECTIN inverted and driven as parallel port nSelectin signal 2 nINIT driven as parallel port nInit signal 1 AUTOFEED inverted and driven as parallel port nAutoFd signal 0 STROBE inverted and driven as parallel port nStrobe signal


Description Microinstructions are either parallel port accesses, program iterations, submicrosequence or C calls. The parallel port must be considered as the logical model described in ppbus(4). Available microinstructions are: #define MS_OP_GET 0 /* get <ptr>, <len> */ #define MS_OP_PUT 1 /* put <ptr>, <len> */ #define MS_OP_RFETCH 2 /* rfetch <reg>, <mask>, <ptr> */ #define MS_OP_RSET 3 /* rset <reg>, <mask>, <mask> */ #define MS_OP_RASSERT 4 /* rassert <reg>, <mask> */ #define MS_OP_DELAY 5 /* delay <val> */ #define MS_OP_SET 6 /* set <val> */ #define MS_OP_DBRA 7 /* dbra <offset> */ #define MS_OP_BRSET 8 /* brset <mask>, <offset> */ #define MS_OP_BRCLEAR 9 /* brclear <mask>, <offset> */ #define MS_OP_RET 10 /* ret <retcode> */ #define MS_OP_C_CALL 11 /* c_call <function>, <parameter> */ #define MS_OP_PTR 12 /* ptr <pointer> */ #define MS_OP_ADELAY 13 /* adelay <val> */ #define MS_OP_BRSTAT 14 /* brstat <mask>, <mask>, <offset> */ #define MS_OP_SUBRET 15 /* subret <code> */ #define MS_OP_CALL 16 /* call <microsequence> */ #define MS_OP_RASSERT_P 17 /* rassert_p <iter>, <reg> */ #define MS_OP_RFETCH_P 18 /* rfetch_p <iter>, <reg>, <mask> */ #define MS_OP_TRIG 19 /* trigger <reg>, <len>, <array> */ Execution context The execution context of microinstructions is: * the program counter which points to the next microinstruction to execute either in the main microsequence or in a subcall * the current value of ptr which points to the next char to send/receive * the current value of the internal branch register This data is modified by some of the microinstructions, not all. MS_OP_GET and MS_OP_PUT are microinstructions used to do either predefined standard IEEE1284-1994 transfers or programmed non-standard io. MS_OP_RFETCH - Register FETCH is used to retrieve the current value of a parallel port register, apply a mask and save it in a buffer. Parameters: 1. register 2. character mask 3. pointer to the buffer Predefined macro: MS_RFETCH(reg,mask,ptr) MS_OP_RSET - Register SET is used to assert/clear some bits of a particular parallel port register, two masks are applied. Parameters: 1. register 2. mask of bits to assert 3. mask of bits to clear Predefined macro: MS_RSET(reg,assert,clear) MS_OP_RASSERT - Register ASSERT is used to assert all bits of a particular parallel port register. Parameters: 1. register 2. byte to assert Predefined macro: MS_RASSERT(reg,byte) MS_OP_DELAY - microsecond DELAY is used to delay the execution of the microsequence. Parameter: 1. delay in microseconds Predefined macro: MS_DELAY(delay) MS_OP_SET - SET internal branch register is used to set the value of the internal branch register. Parameter: 1. integer value Predefined macro: MS_SET(accum) MS_OP_DBRA - Do BRAnch is used to branch if internal branch register decremented by one result value is positive. Parameter: 1. integer offset in the current executed (sub)microsequence. Offset is added to the index of the next microinstruction to execute. Predefined macro: MS_DBRA(offset) MS_OP_BRSET - BRanch on SET is used to branch if some of the status register bits of the parallel port are set. Parameter: 1. bits of the status register 2. integer offset in the current executed (sub)microsequence. Offset is added to the index of the next microinstruction to execute. Predefined macro: MS_BRSET(mask,offset) MS_OP_BRCLEAR - BRanch on CLEAR is used to branch if some of the status register bits of the parallel port are cleared. Parameter: 1. bits of the status register 2. integer offset in the current executed (sub)microsequence. Offset is added to the index of the next microinstruction to execute. Predefined macro: MS_BRCLEAR(mask,offset) MS_OP_RET - RETurn is used to return from a microsequence. This instruction is mandatory. This is the only way for the microsequencer to detect the end of the microsequence. The return code is returned in the integer pointed by the (int *) parameter of the ppb_MS_microseq() function. Parameter: 1. integer return code Predefined macro: MS_RET(code) MS_OP_C_CALL - C function CALL is used to call C functions from microsequence execution. This may be useful when a non-standard i/o is performed to retrieve a data character from the parallel port. Parameter: 1. the C function to call 2. the parameter to pass to the function call The C function shall be declared as a int(*)(void *p, char *ptr). The ptr parameter is the current position in the buffer currently scanned. Predefined macro: MS_C_CALL(func,param) MS_OP_PTR - initialize internal PTR is used to initialize the internal pointer to the currently scanned buf- fer. This pointer is passed to any C call (see above). Parameter: 1. pointer to the buffer that shall be accessed by xxx_P() microsequence calls. Note that this pointer is automatically incremented during xxx_P() calls Predefined macro: MS_PTR(ptr) MS_OP_ADELAY - do an Asynchronous DELAY is used to make a tsleep() during microsequence execution. The tsleep is executed at PPBPRI level. Parameter: 1. delay in ms Predefined macro: MS_ADELAY(delay) MS_OP_BRSTAT - BRanch on STATe is used to branch on status register state condition. Parameter: 1. mask of asserted bits. Bits that shall be asserted in the status register are set in the mask 2. mask of cleared bits. Bits that shall be cleared in the sta- tus register are set in the mask 3. integer offset in the current executed (sub)microsequence. Offset is added to the index of the next microinstruction to execute. Predefined macro: MS_BRSTAT(asserted_bits,clear_bits,offset) MS_OP_SUBRET - SUBmicrosequence RETurn is used to return from the submicrosequence call. This action is manda- tory before a RET call. Some microinstructions (PUT, GET) may not be callable within a submicrosequence. No parameter. Predefined macro: MS_SUBRET() MS_OP_CALL - submicrosequence CALL is used to call a submicrosequence. A submicrosequence is a microse- quence with a SUBRET call. Parameter: 1. the submicrosequence to execute Predefined macro: MS_CALL(microseq) MS_OP_RASSERT_P - Register ASSERT from internal PTR is used to assert a register with data currently pointed by the internal PTR pointer. Parameter: 1. amount of data to write to the register 2. register Predefined macro: MS_RASSERT_P(iter,reg) MS_OP_RFETCH_P - Register FETCH to internal PTR is used to fetch data from a register. Data is stored in the buffer cur- rently pointed by the internal PTR pointer. Parameter: 1. amount of data to read from the register 2. register 3. mask applied to fetched data Predefined macro: MS_RFETCH_P(iter,reg,mask) MS_OP_TRIG - TRIG register is used to trigger the parallel port. This microinstruction is intended to provide a very efficient control of the parallel port. Triggering a register is writing data, wait a while, write data, wait a while... This allows to write magic sequences to the port. Parameter: 1. amount of data to read from the register 2. register 3. size of the array 4. array of unsigned chars. Each couple of u_chars define the data to write to the register and the delay in us to wait. The delay is limited to 255 us to simplify and reduce the size of the array. Predefined macro: MS_TRIG(reg,len,array)


C structures union ppb_insarg { int i; char c; void *p; int (* f)(void *, char *); }; struct ppb_microseq { int opcode; /* microins. opcode */ union ppb_insarg arg[PPB_MS_MAXARGS]; /* arguments */ }; Using microsequences To instantiate a microsequence, just declare an array of ppb_microseq structures and initialize it as needed. You may either use predefined macros or code directly your microinstructions according to the ppb_microseq definition. For example, struct ppb_microseq select_microseq[] = { /* parameter list */ #define SELECT_TARGET MS_PARAM(0, 1, MS_TYP_INT) #define SELECT_INITIATOR MS_PARAM(3, 1, MS_TYP_INT) /* send the select command to the drive */ MS_DASS(MS_UNKNOWN), MS_CASS(H_nAUTO | H_nSELIN | H_INIT | H_STROBE), MS_CASS( H_AUTO | H_nSELIN | H_INIT | H_STROBE), MS_DASS(MS_UNKNOWN), MS_CASS( H_AUTO | H_nSELIN | H_nINIT | H_STROBE), /* now, wait until the drive is ready */ MS_SET(VP0_SELTMO), /* loop: */ MS_BRSET(H_ACK, 2 /* ready */), MS_DBRA(-2 /* loop */), /* error: */ MS_RET(1), /* ready: */ MS_RET(0) }; Here, some parameters are undefined and must be filled before executing the microsequence. In order to initialize each microsequence, one should use the ppb_MS_init_msq() function like this: ppb_MS_init_msq(select_microseq, 2, SELECT_TARGET, 1 << target, SELECT_INITIATOR, 1 << initiator); and then execute the microsequence. The microsequencer The microsequencer is executed either at ppbus or adapter level (see ppbus(4) for info about ppbus system layers). Most of the microsequencer is executed at ppc level to avoid ppbus to adapter function call over- head. But some actions like deciding whereas the transfer is IEEE1284-1994 compliant are executed at ppbus layer.


ppbus(4), ppc(4), vpo(4)


The microseq manual page first appeared in FreeBSD 3.0.


This manual page was written by Nicolas Souchu.


Only one level of submicrosequences is allowed. When triggering the port, maximum delay allowed is 255 us. DragonFly 4.7 June 6, 1998 DragonFly 4.7

Search: Section: